Search results

  1. C

    Clock Jauch gathering pallet

    Jauch gathering pallet for a triple chime pull up
  2. C

    Help Patti strike movement repair

    Thank you all for the help I will try all your ideas I am also getting another patti movement next week so I can compare them I will comment again afterwords although I have been doing this 25 years this is my first patti thank heaven for nawcc and you folks
  3. C

    Help Patti strike movement repair

    just had it off for the picture, do not worry, I have it
  4. C

    Help Patti strike movement repair

    Thank you RC and shutterbug. I installed those 2 helper springs to try to solve my problem but the count wheel still moves when I wind it setting off the train I am at a loss on how to proceed, I have followed the set up instructions you have sent in your last post, looked at your new post of...
  5. C

    National Meeting Finding Friends and other with interests like yours

    Peter Elmendorf I can not find my tables on the map 1932, 1933,1934
  6. C

    B. B. Lewis calendar clock

    I need the pendulum length for a restoration, tried the formula but it seems too short, maybe I counted wrong, I will have tables at the national, so if you have one there, let me know and I will measure it, thanks, Peter Elmendorf RIP chapter 40
  7. C

    Clock parts wanted Obsolete older posts II

    I am trying to send a new post. I need a French barrel: diameter over teeth is 1.600", diameter over end of barrel is 1.475", width is .990", 80 teeth on the barrel, barrel is marked 2-24, thank you, Peter Elmendorf
  8. C

    english 8 day rack striking problem

    rotating the gp 90 degrees has solved the problem, giving it a little more time to finish striking, thanks for all the help!
  9. C

    english 8 day rack striking problem

    Thank you so much for the additional analysis, I believe between the 2 of you , you are focusing in on the solution.
  10. C

    english 8 day rack striking problem

    Dear Shutterbug, Thank you for the gp suggestion, this makes sense, at present the movement has stopped this odd behavior without my making any changes, further report will follow, Peter Elmendorf
  11. C

    english 8 day rack striking problem

    Thank you for your suggestion. I will try this. Kindest regards, Peter
  12. C

    english 8 day rack striking problem

    At various hours, the clock, which is about 200 years old, will strike all but one, such as 4 at 5, leaving the hammer on the rise, and the warning pin back at the 12 oclock position where it is when it finishes striking and the gathering pallet resting on the pawl pin as it should be when it is...
  13. C

    english 30 hour longcase continuous chain striking train problens

    After utilizing the suggestion from P. Hageman I found it helpful to ensure that the hoop wheel lever was in the far end of the slot, seen as the hoop wheel rotates toward the lever. As well, on closer inspection I noticed a small arrow between two of the teeth on the count wheel and a slashed...
  14. C

    english 30 hour longcase continuous chain striking train problens

    thank you so much for this very helpful and timely information
  15. C

    english 30 hour longcase continuous chain striking train problens

    additional info on my clock: There is a hoop wheel which receives a square shaped lever to stop the strike. The lever I have shown is the detent strike lever. It is on the same arbor as this hoop wheel stop lever mentioned previously. This detent strike lever is the one that gets jammed in the...
  16. C

    english 30 hour longcase continuous chain striking train problens

    This circa 1850 movement has been rebuilt by me. In testing it stops right before the warning as the strike train tends to creep and jams the strike detent against the edge of the slot in the strike wheel. In order to avoid the hammer being on the rise, allow for warning run, and have the clock...
  17. C

    French Marti Rack and Snail Strikes 2 at highest point on snail where one should be

    Re: French Marti Rack and Snail Strikes 2 at highest point on snail where one should I made a template after measuring how far the rack tail would travel for one tooth of the rack. I then opened up the angle between the rack and the rack tail by that amount. Now it works perfectly striking 1...
  18. C

    French Marti Rack and Snail Strikes 2 at highest point on snail where one should be

    Re: French Marti Rack and Snail Strikes 2 at highest point on snail where one should I thank you 3 gentleman for your excellent suggestions, as usual with this fine forum, the answers come faster than I can apply them, but I will let you know how things work out, this is the last issue left...
  19. C

    French Marti Rack and Snail Strikes 2 at highest point on snail where one should be

    I have lined up the 3 dots on the appropriate gears, and it strikes ok at 12, 12:30 but when it reaches the 1:00 position the rack falls all the way down and can not be gathered, so the strike runs completely down. At what should be one on the snail, the highest point on the snail, it strikes...
  20. C

    AhHa cad cam software and control board

    John, Thanks so much, Peter
Our 2021 National Meeting in Hampton Roads Virginia
Topic related ad experiment
Know Your NAWCC Forums Rules!
RULES & GUIDELINES

Find member

Forum statistics

Threads
160,883
Messages
1,395,801
Members
82,887
Latest member
Nathanaweigh
Encyclopedia Pages
1,099
Total wiki contributions
2,787
Last edit
How to wire a 24 volt secondary for a 12 volt ITR/IBM Master clock system by Toughtool