Search results

  1. J

    Synchronous clock lubrication

    OK Mike, I stand corrected on the oil for the motor and completely agree re WD 40!. I am on the Gloucestershire/Worcestershire border area.
  2. J

    Synchronous clock lubrication

    Clock oils are good because they are formulated not to dry out or go 'gummy'. As a general 'rule of thumb', pivots (i.e. where a shaft rotates in a bearing/plate/support/tube) should be oiled - very sparingly. Gear trains (i.e. the gear teeth themselves) should usually be clean and dry. Being...
  3. J

    syncronome tower clock

    C421 dates to either late 1931 or early 1932, so about 90 years old. It is one of the "Coventry" series, made for Synchronome under contract in Coventry (UK) - designated by the C prefix. A distinguishing feature is a smooth inside radius to the bend of the gravity arm. Normal (i.e...
  4. J

    my Synchronome set

    Thank you for the pictures. The 3 slave dials with the convex glass and 'fancy' hands are unusual. I have not seen that pattern before. The copper cased one and the two wooden based ones are well known types. The master having green coil wire dates to pre about 1953.
  5. J

    syncronome tower clock

    A master and 5 slaves needs about 4.5 Volts (DC) for the master including it's inbuilt dial, and 1.5 Volts per external slave, so a 12 Volt supply should be absolutely fine. Current is 330 mA and the duty cycle is very low (roughly 100 milliseconds impulse every 30 seconds). This can be...
  6. J

    syncronome tower clock

    The larger Synchronome slave movements used two coils - running at a nominal 330 mA impulsed every 30 seconds (hence 120 teeth on the minute hand wheel). The two coil movements are most often seen on the Synchronome 'programme controllers' used to ring bells in schools, factories etc. but were...
  7. J

    syncronome tower clock

    You are quite right! It was my mistake to omit Gents (probably the most popular and well known of them all in the UK) from the group of "Synchronome, Lowne, Silent Electric, Gents". The Thornbridge, C6, C7 were all 30 second. Some of the later Gents (Chronopher) were 1 minute. Gents did some...
  8. J

    syncronome tower clock

    120 teeth on the wheel so half minute per pulse. Half minute impulses were standard (at that period) for most of the British master/slave clock systems (Synchronome, Lowne, Silent Electric) and the later Gillett & Johnston and English Clock Systems (ECS/Smiths). 1 minute impulse systems were...
  9. J

    syncronome tower clock

    If you could get a picture of the master clock - that would be great - if it is the original, the serial number on the bottom of the NRA plate (see attached) can give a good idea of the date for you. As a guide, serial number 100 was issued circa 1910 and by 1915 up to about 500. Early master...
  10. J

    syncronome tower clock

    The date given in the first post seems to tie in with the clock movement. The wooden former resistor (wired in parallel with the coils for spark suppression) was used up to around the mid 1920s. but the font and case used for the patented stamp was changed, probably around 1915, from the upper...
  11. J

    C7 Temperature stability

    Gent's own "see saw" mechanism can be seen on Clockdoc.org under Gents/Synchronisers/see saw
  12. J

    C7 Temperature stability

    The Gents pendulum rod should be Invar (unless it is a VERY early clock pre about 1910 which used a wooden rod). Invar should in itself give a good degree of temperature stability, but 25 degrees C is a wide range. I don't believe there is any 'compensation' as such used, but I may be wrong on...
  13. J

    Gents Gents leicester Hipp toggle master help required

    I can't give you a definitive answer and what follows is 'educated guesswork', but Gents C7 were designed for 220 mA series operation, but did come in different versions. I have one that was designed for use on 48V. Could it be a clue that your terminal board has a "50 Volt battery" set of...
  14. J

    Synchronome Minute Masters

    I am gathering data about Synchronome Minute Masters. These clocks, made between circa 1960 and 1970(ish) have a 3/4 second pendulum, Hipp toggle pendulum drive and a 1 minute single polarity impulse. My interest was triggered when a friend recently acquired a clock whose serial number was...
  15. J

    Need help for Synchronome Masterclock with seconds contact

    The link included in my last post should be able to supply to Germany I think. These are widely available as Brocot jewels with at least 3 suppliers in the UK. They would not recognise it as a 'Synchronome' part though.
  16. J

    Need help for Synchronome Masterclock with seconds contact

    You can buy the jewels. In the UK they can be got here Pallet Stones, Ruby (Brocot). You can just search for "Brocot Jewel" for a local supplier. You do need to get the right diameter. Mine measures 3mm as near as I can measure it, but you should check the hole dimensions. Note that you...
  17. J

    FAVARGER & CO

    I know nothing about it - but this may help Peyer Favarger &Co Suc. M. Hipp, Swiss slave clock 1900 | #32816106. It seems that Peyer Favager were successors to Mateus Hipp. There is a section on Hipp on the Clockdoc.org website.
  18. J

    Synchronome Clock

    If they stop with the gravity arm 'down' - it is usually an electrical issue (including contacts). Check current is approx 300 - 330 mA with the contacts closed. If they stop with the gravity arm up - it is usually a friction and/or cleanliness issue. Check that the gathering jewel just...
  19. J

    Mixing Synchronome & Gents slave dials

    You may well consider me incompetent, lazy - even both. I don't come to these forums though laziness - and if you think me incompetant and lazy - frankly it isn't a very helpful reply to anyone. The approach I have used is both practical and pragmatic.
  20. J

    Eureka Eureka Clock Co., London

    Picture of a (rather dirty!) contact and flag in situ. The 'pin' has a silver(?) conductive part on the side nearest the camera and an insulated side on the side away from the camera. As the photo is set up, the insulated side of the pin is resting against the flag. The pin passes down...

Forum statistics

Threads
174,389
Messages
1,523,832
Members
52,191
Latest member
tlegare72
Encyclopedia Pages
1,063
Total wiki contributions
2,971
Last page
Hard Life for Wristwatches by Roy Gardner