Goal: $300, Received: $30.00 (10%) Contribute Now
Donate whatever you can or Join the 14,000 other NAWCC members for only $80 (plus $10 for hard copy publications). Check it out here.

Results 1 to 3 of 3
  1. #1

    Default Gents C7 Pulsynetic Master Clock Power Supply

    Click image for larger version. 

Name:	20170511_194514.jpg 
Views:	13 
Size:	341.7 KB 
ID:	343701Click image for larger version. 

Name:	20170511_195014.jpg 
Views:	15 
Size:	266.5 KB 
ID:	343702Click image for larger version. 

Name:	20170511_195017.jpg 
Views:	11 
Size:	265.1 KB 
ID:	343703

    I purchased this stunning Gents master clock from an auction after falling for its industrial good looks. I have no experience of owning clocks or in this case powering them, so was hoping I could get some advice on how to power, set up and run the clock. Serial No: 9232 Date 10-01-1955
    I will only be powering the master clock as have no need for slave clocks around the house. If possible I would like to power the clock direct from the house mains, and do away with batteries and recharging.
    In the back of the cabinet is a sticker from a previous owner stating that the clock can be operated from a 4.5volt battery, so potentially has the clock ben adapted/adjusted?
    I was considering purchasing a multi volt mains adaptor that can supply a range of voltages,
    The following specification is for one off eBay.
    Input: AC 100-240V 0.25A 50/60Hz 12W UK 3 Pin Plug
    Output: DC 3, 4.5, 5, 6, 7.5, 9, 12V
    USB output: 5.0V 2.1A

    I am aware that it is the amp rating that is critical so could you advise on the most suitable supply and how and where exactly I would attach the supply to the clock.

    How do I start the clock and set the time?

    Any help, knowledge or guidance would be much appreciated, and please consider I am a carpenter rather than an electrician, so layman terms if you can.

  2. #2
    Registered User Hans Vrolijk's Avatar
    Join Date
    Jan 2005
    Rotterdam, The Netherlands

    Default Re: Gents C7 Pulsynetic Master Clock Power Supply (By: clive449)

    There should be a terminal on the right upper inner site of the case. You need 220 milli amps so a power supply as mentioned will do.On the back of the frame is a lever: by pulling the rope the contact closes on every swing of the pendulum and the dial slave will advance.

    I can send you a Pdf of the manual of this clock. Unfortunately the file is to big to attach to this site. You can mail me at: jjhvrolijk@solcon.nl
    Interested in my electric clocks?

  3. #3

    Default Re: Gents C7 Pulsynetic Master Clock Power Supply (By: Hans Vrolijk)

    Hi Hans

    Thank you for your reply, could I message you a picture of the terminal location in my clock to confirm I am attaching the positive and negative in the right place. I will order the plug today and message you when ready to fit.

    thank you again


Similar Threads

  1. Gents Pulsynetic Master Clock - advice required
    By puffernutter in forum Electric Horology
    Replies: 20
    Last Post: 03-14-2017, 07:26 PM
  2. Correct Voltage for Gents Pulsynetic Master Clock
    By Lincolnhill in forum Electric Horology
    Replies: 70
    Last Post: 03-10-2017, 04:09 PM
  3. Gents Pulsynetic Master Clock Instructions
    By NANETTE in forum Electric Horology
    Replies: 2
    Last Post: 03-04-2017, 12:03 PM
  4. Gents C7 Pulsynetic master clock internal circuitry
    By dennishoy in forum Electric Horology
    Replies: 3
    Last Post: 01-06-2016, 04:55 AM
  5. IBM Master clock Power supply?
    By eskmill in forum Clock Repair
    Replies: 1
    Last Post: 02-08-2005, 11:48 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts