Goal: $300, Received: $30.00 (10%) Contribute Now
Donate whatever you can or Join the 14,000 other NAWCC members for only $80 (plus $10 for hard copy publications). Check it out here.

Results 1 to 8 of 8
  1. #1

    Default Tool and Tool Parts Wanted

    Post your request for tools and tool parts here. Please post a follow-up, or notify me by Private Message, when your request has been satisfied so I can remove your request. Please conduct any transactions by Private Message.

  2. #2
    Registered user.
    Join Date
    Mar 2011

    Default Re: Tool and Tool Parts Wanted (By: Dave Coatsworth)

    There are some parts I have been looking for for decades to complete my lathe sets (Lorch, Schmidt & Co. and Wolf, Jahn & Co.):

    - A 90° steady for D-bed lathes (I only ever saw one on ebay and didn't get it):

    - A collet-holding screw-tailstock for WW-lathes

    - A rotating head-stock for WW-lathes

    - A set of or individual wheel-chucks for a WW-lathe:

  3. #3
    Principal Administrator John Hubby's Avatar
    Join Date
    Sep 2000
    The Woodlands, TX

    Default Emco Compact 5 Drive motor and switch (By: Dave Coatsworth)

    The control switch and starter capacitor for my Emco Compact 5 lathe have finally died (34 years old and lots of use). The drive motor is probably OK but all this is 240V 50 cycle as I bought the lathe while living outside the US. Would like to replace these three elements with 120 V 60 cycle parts, looking for any availability at reasonable price.

  4. #4
    Registered User
    Join Date
    May 2001
    Northern Wisconsin

    Default Re: Emco Compact 5 Drive motor and switch (By: John Hubby)

    John, Check on ebay for emco compact 5, there are a couple of motors with the switch listed, if I remember they are about $150.00 or so. Other wise you could check at a motor shop for a capacitor and switch.

    Good luck, Curly

  5. #5

    Default Re: Emco Compact 5 Drive motor and switch (By: curly)

    Grainger supply may have your capacitor, or eve a local Air conditioner supply.

  6. #6

    Default Looking for a Jig Bore (By: Dave Coatsworth)

    I'm looking for a Jig Bore. I prefer a Hauser M1, 2A3, or 2BA. I'm open to other models if comparable.


  7. #7
    Registered user.
    Join Date
    Jun 2013
    Toronto, CANADA

    Default K&D Inverto 17 Anvil Plate wanted (By: MNowlin)

    I'm looking for the anvil plate ONLY for a K&D Inverto 17 staking tool. The anvil plate I currently have my Inverto 17 seems not to be original, because there are holes spread over the plate, that some of the holes don't line up to the arm and there is no hole large enough to accept a stake in the inverted position. I am not too fussy on condition of the plate so long as it is serviceable.
    - Robert

  8. #8
    Registered User
    Join Date
    Dec 2011
    Brockville, On Canada

    Default Re: K&D Inverto 17 Anvil Plate wanted (By: robmack)

    You might contact Larry and see if he has bits and pieces that aren't on his site.


    David S

Similar Threads

  1. Demagnetizing parts and tools?
    By mikeukrainetz in forum Watch Repair
    Replies: 10
    Last Post: 02-11-2016, 02:22 PM
  2. Who are your Watch Parts and Tools Suppliers?
    By bchaps in forum Watch Repair
    Replies: 15
    Last Post: 08-22-2008, 12:16 PM
  3. stolen Parts and tools and watches.
    By EmmaR in forum Lost or Stolen Horological Items
    Replies: 2
    Last Post: 07-01-2008, 12:18 PM
  4. Generic tool parts wanted.
    By wynter in forum Horological Tools
    Replies: 1
    Last Post: 08-12-2001, 10:09 AM
  5. Needle in a haystack tool part wanted
    By wynter in forum Horological Tools
    Replies: 1
    Last Post: 07-24-2001, 03:35 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts